OxyTurbine development department
Kozlovičeva Ul. 21
Slovenia – EU
PayPal: email@example.com / IBAN: SI56 1010 0001 0223 407 / Swift: BAKOSI2X /
Marija Dravinec / Stritarjeva Ulica 6 / SI6000 Koper / VAT: 76971325 / Slovenia – EU
GOODS ARE V.A.T. FREE ACCORDING TO ARTICLE 46. PARA a LAW ON V.A.T. The exporter of the products covered by this document declares that, except where otherwise, clearly indicated, these products are of Slovenia Europe preferential origin. Payment conditions: 100% advance before dispatch.
OxyTurbine air turbine uses the twin physics principles of precession (as applied to rotating fluids) and centrifugal force. Precession creates a low-pressure zone within the subsurface rotating turbine that draws in surface air from the atmosphere. Once inside the turbine chamber, this air is discharged rapidly into the surrounding water through the power of centrifugal force.
There are two critical factors that distinguish turbine aerator from another aerator. First, the centrifugal force slings the air out at a high-speed in a lateral direction more than a 100-foot diameter. Second, tests in a clear water tank have shown that the dissolved oxygen is also pushed down for ten feet or more below the surface. These forces create a mixing action that disperses the dissolved oxygen throughout the pond. Of great significance, many of the oxygen clusters have been measured to be less than 0.25 millimeters in diameter. This “bubble” size in the water is much too small to be seen with the naked eye even in a clear water tank. Such small clusters tend to migrate from areas of high concentration, such as near the rotating turbine, to regions of low density. This phenomenon helps disperse the dissolved oxygen throughout the pond well beyond the 100-foot radius referenced above.
OxyTurbine, air turbine aerator, requires no routine maintenance. There are no bearings to grease or performance adjustments to be made. The floating aerator uses foam-filled; UV-protected, polyethylene pontoons guaranteed not to sink. The motors are heavy-duty, industrial-grade, designed to run 24/7. The air shaft is made of a stainless steel tube that has a ¼-inch thick wall. The rotating turbine is made of fiberglass resin that is both corrosion and wears resistant. The aerator prefers to be left alone once it is turned on, i.e., no need for regular inspections. See the image of the turbine on this page.
Splash aerator attempt to oxygenate ponds by throwing vast amounts of water into the air. The hope is that the water will pick up atmospheric oxygen as it falls back into the dugout. The challenge is that the exposure time of the water to the air is too short for optimal oxygen saturation of the water droplets. Also, these aerators tend to aerate only the top surface of the pond with a rather large air bubble that escapes quickly back into the atmosphere. A further shortcoming is that splash aerator has an insufficient ability to disperse the dissolved oxygen in a lateral direction around the pond. Finally, because water is heavy and dense, it takes enormous amounts of energy in the form of large, costly motors to throw the water into the air.
In contrast to the above, the turbine aerator is a state-of-the-art aerator that oxygenates by injecting air into water and not water into the air. It takes a lot less energy to push air into liquid compared to water into the air. This is the reason the turbine aerator can outperform competing for aerator having up to seven times more horsepower.
There are other side benefits to the Turbine aerator. In climates where freezing weather occurs, splash or paddle wheel aerator tend to freeze and must be shut down. The OxyTurbine aerator is not affected by such freezing weather and can continue to run year around. Another benefit is the savings in electrical costs over competing for aerator as discussed below. Regarding the surfactants issue: OxyTurbine principals have had some experience with surfactants in water that was oxygenated. It likely is impossible to drop the foaming issue entirely. However, foaming seems to be much less of an issue if the injection and mixing of the air are performed on the surface. Any splashing or thrashing of the water at the surface tends to exacerbate the foaming of the surfactants.
Electrical Cost Savings
Some clients are reporting a drop in electrical costs of as much as 50% when they replace their existing aerator with our aerator. Surprisingly, this reduction in electrical costs is occurring even as the dissolved oxygen levels in their ponds are rising much. Such results are seemingly impossible given that the aerator being replaced have up to seven times more Horsepower than the Turbine aerator. These results stem partly from the inefficient, outdated aerator these clients are replacing as well as from the superior performance of the turbine aerator.
Because the turbine’s superior performance is straightforward, the turbine combines the best principles of first bore bubble diffuser with the mixing action of prop aerator. Stated differently, the turbine’s rotating blades shear or slice the oxygen bubbles into sizes that typically are only seen in fine-bore bubble diffuser. Unlike such diffusers, however, there are no emitters that can clog, plus the turbine actively disperses these microbubbles around the pond in a way not possible by a static diffuser. The turbine further combines turbulent flow at the surface with the laminar flow at depths. This laminar flow causes some of the deep water to rise to the surface, being escorted up by the slowly rising air bubbles. At the surface, this water is oxygenated before it once again drops to the lower levels of the pond.
While it might be useful to speak of pounds of oxygen per hour or per horsepower-hour, these terms often overlook some genuine issues of oxygen saturation, not to mention the financial considerations facing the plant manager. The more critical and often ignored keys of a good aerator are:
1.) bubble size and buoyancy, 2.) oxygen dispersion rates, 3.) motor horsepower and attendant electrical usage, 4.) maintenance and repair costs, 5.) ease of removing and replacing the aerator into the pond as needed, and 6.) the availability and cost of replacement parts. These are the areas where the OxyTurbine aerator can significantly outperform its competition, particularly about electrical usage.
Existing splash aerator of 75 to 100-horsepower, if operating at a full amperage load, would draw between 70 and 90 amps, respectively, at 575 volts. This equates to 40,000 and 52,000 watts each (Eg. 70 amps x 575 volts = 40,250 watts). In contrast, OxyTurbine 5-horsepower aerator, if operating at a full amperage load, would draw five amps at 575 volts. This equates to 5 x 575 = 2875 watts. As seen below, we recommend a minimum of 3 of its aerator to replace each of the 75 hp splash aerator (15 hp total replacing 75 hp). Three aerator at 2875 watts each equates to 3 x 2875 watts = 8625 watts. Based on wattage alone, the three Turbine aerator would pull roughly 8625 w/40,000 w = 21 % of the electrical power of a 75-hp splash aerator. This analysis assumes the same operating time and the same kilowatt-hour electrical cost in both situations. Regarding the 100 hp aerator, we suggest that 4 of its aerator be used to replace these larger splash aerator (20 hp total replacing 100 hp). Based on wattage, 4 Turbine aerator would pull 4 x 2875 w = 11,500 watts. Thus, four Turbine aerator would pull 11,500 w/52,000 w = 22% of the electrical power required by a 100-hp splash aerator. It should be obvious that even if more Turbine aerator is needed than is being recommended, the SAVINGS IN POWER COSTS alone will pay for the OxyTurbine aerator in short order.
The cookie settings on this website are set to "allow cookies" to give you the best browsing experience possible. If you continue to use this website without changing your cookie settings or you click "Accept" below then you are consenting to this.